How to Use Driver Setup Rule

Driver Setup Rule

	The Driver Setup Rule assigns drivers to consists and issues them with Driver Commands.
	Driver Commands are lists of instructions or "orders" that drivers are tasked to complete under the control of the Trainz AI system.

The Driver Setup Rule is automatically added to the Session Editor of every route and Session.

Open the Surveyor Session Editor by selecting Edit Session from the Surveyor main menu.

Steps: Select the Driver Setup Rule shown left (it is usually the rule at the top of the list) Click the Edit button at the bottom of the Session Editor window If the Driver Setup Rule is not shown in the list then... Click the Add button at the bottom of the Session Editor window Scroll through the list of rules to locate and select the Driver Setup Rule Click the Tick button on the rule list window

Adding New Drivers

After selecting the Driver Setup Rule and clicking the Edit button, the Driver Setup Properties Window will be shown. The image below shows the properties window if it is opened with no locomotives placed in the layout.

Settings: When the above option is Checked, randomly selected drivers will be assigned to all newly added driveable trains. Existing drivers will not be affected If Unchecked then you will have to manually assign drivers to trains by clicking the Add another Driver link When using the Driver Setup Rule for the first time with no drivers assigned to existing trains, the Generate new Drivers for empty trains option will immediately assign drivers to each train. Each time a new train is added to the layout, it will be automatically assigned a driver. Known Issues: This does not appear to have any effect

Editing the Driver List

When drivers and trains have been added to the rule, it will appear as shown below.

The first driver in the list will be given the camera focus when the Session is started. Unfortunately, there is no easy way of moving drivers up and down the list order. If a loco name appears in red then it has been removed from the layout. Steps: Click on the driver icon to select a different driver from the Session list. Click on the loco name to select a different loco from the Session list (an empty loco list means no unassigned locos are available). Click on the driver name to type in a new name for this driver (this will not change the driver icon). Click on Autodetect to select a new owner for this driver and loco. There are four "owner" options:- AI driver - this train will be under AI control even if it has no Command Bar orders to follow. This can be used to prevent a user from taking control of the train. Autodetect - if the train has Command Bar orders then it will be under AI control. If it has no Command Bar orders then it will be under user control. First Human Player - the train will be assigned to the user or a multiplayer, whoever selects it first. Multiplayer Driver - the train will be assigned to a multiplayer. If you need to remove a driver:- Click remove to delete this driver from the rule.

Adding Driver Commands

The grey area below the driver details (name, loco, owner) is the Driver Command Bar. This is where the driving instructions (the "train orders") used by the Trainz AI system are given to the driver.

Shown below is a Command Bar after two Driver Commands have been added. Each command has its own icon. Move the mouse pointer onto a command icon to reveal a tooltip showing the contents of the command, as shown in the image.

Steps: Click the small "double chevron" icon shown in the image on the left. This will open a Command List menu which will show the driver commands that can be added to this drivers Command Bar. Click on a command to add it to the Command Bar. Notes: The commands that will be shown and are available for use are decided by another rule, the Driver Command Rule. If a command that you want is not in the list then open and edit the Driver Command Rule. Many of the items in the menu will open sub-menus. For example:- The Drive To Trackmark will open a sub-menu listing all the available trackmarks The Navigate To will open a sub-menu of all the interactive industries The Wait For will open a sub-menu of different wait times

When a driver command has been executed in Driver Mode by the Trainz AI system, it will be deleted from the Command Bar and the next command in the sequence will then be executed. This will continue until the last command has been executed and deleted. Then the AI control of the train will terminate.

Deleting Driver Commands

To remove a command from the Command Bar...

Steps: Click on the command and hold down the left mouse button Drag the command out of the Command Bar area

The "Repeat" Command

The "Repeat" command is a special built in command that allows all the driver commands to be repeated endlessly.

The "Repeat" command is only available when at least one command is present in the Command Bar. Only one Repeat command can be added to a Command Bar. Steps: Click the Add Command button on the Command Bar Select the Repeat option

The Repeat icon will always be placed at the end of the Command Bar after the Add Command button. Notes: As each command is executed by the Trainz AI system, it will be deleted from the front of the command list and added to the end of the list.

Notes: If a Repeat command is already present, then the Add Command menu list will show Don't Repeat as its first option Select Don't Repeat to remove the Repeat command

Known Issues: If a Repeat command is present in the Command Bar and all the other commands are then deleted, the Repeat command will remain in the Command Bar and cannot be removed. Because there are no other commands to be repeated this will not cause a problem. However when later adding new commands the presence of the Repeat command can be easily overlooked.

Workaround: Add a command (any command) to the Command Bar. The Don't Repeat option will then become available and the Repeat command can be removed.

Driver Command Rule

	The Driver Command Rule controls which Driver Commands will be available in a Session. This applied to both:- Driver Commands added to the Driver Setup Rule in the Session Editor in Surveyor Mode, and Driver Commands for the user to manually add to the Command Bar of user and AI controlled trains running in Driver Mode.
	Removing commands such as Navigate To will force players to manually drive trains when in Driver Mode instead of allowing them to use the Trainz AI system to do all the work.

Open the Surveyor Session Editor by selecting Edit Session from the Surveyor main menu.

Steps: Select the Driver Command Rule shown left (it is usually the rule near the top of the list) Click the Edit button at the bottom of the Session Editor window If the Driver Command Rule is not shown in the list then... Click the Add button at the bottom of the Session Editor window Scroll through the list of rules to locate and select the Driver Command Rule Click the Tick button on the rule list window This will add the rule to the Session Editor.

The Rule properties window will open to show all the Driver Commands that have been installed in TANE on your system. This list includes the commands that are built into TANE and those that have been downloaded from the DLS.

Settings: Commands that are Checked ON will be available in the Driver Setup Rule Command List in the Session Editor and for the user in Driver Mode Commands that are Checked OFF will NOT be available in the Driver Setup Rule Command List in the Session Editor and for the user in Driver Mode To change the status of a command simply check it ON or OFF Notes: Some Driver Commands that have been checked ON will not appear in the Command List if there is no target for their action. For example: The Wait For Trigger command will not be available to any drivers if there are no triggers set. The Call At command will not be available to any drivers if there are no industry active assets or passenger enabled stations. If a command that you want to use does not appear in the list, then check in Content Manager that it has been installed or downloaded and is free of errors.

---

---

Trainz Wiki

• How to Guides
• Session Rules List (Alphabetical) with Parameters
• Session Rules List (Categories) With Parameters

Route Creation Tutorials:

• Merging Routes
• Using the Bulk Asset Update/Replace Tool
• Using Layers

Session Creation Tutorials:

• Adding Message Popups
• Adding Message Popups - Applications
• Adding Navigation Points
• Adding Navigation Points - Applications
• Controlling Junctions in Sessions
• Controlling Signals in Sessions
• Creating a HTML Asset (Session Introduction Page and In Game Messages)
• List of Parent Rules
• Parent and Child Rules
• Using Track Triggers
• Using Variables in Sessions - Examples