Revision as of 13:29, 25 May 2020

The Tools Menu (F5) offers some additional tools for helping to create your Trainz world.

Ruler Management Tools

Ruler elements are available in Surveyor and serve 3 purposes:

• They are used to measure distances (track lengths, radius when laying curves, even the size of your basement or garage.)
• They provide straight lines which can be used to make sure that multi-point splines are indeed aligned straight.
• They provide angular measurement, showing their angle relative to the world north-south axis.
  
  

Rulers are the essential Surveyor tool for modeling anything from the real world in Trainz. They are always hidden in Driver.

Add Ruler

To add a ruler, Click on Add Ruler (R), then Click at your chosen point in your terrain and drag the mouse to the other end point for the ruler and release the mouse button. The ruler stretches out just like you experienced with spline objects, except a ruler cannot be segmented, it is limited to two endpoints.

Ruler scale (e.g. Real Scale, HO scale, OO scale, etc...) and units (metric or imperial) are set by the properties of the route (i.e. the Surveyor 'Edit Route' menu item).

As rulers render themselves above the terrain level, you should always plant your first point while the camera is viewing from directly overhead, or else it will likely be mislocated due to the bias of your viewing angle. As the second endpoint is dragged with the mouse to its final location, the ruler conveniently displays its length, scale, and angle to north-south in a continuous fashion. Therefore, you can make a ruler a specific length and/or angle if you manipulate it carefully.

Note that rulers obey layering behavior just like objects and splines. Be conscientious what layer you are placing a ruler on because once placed, there is no facility to read what layer it resides on if you need to move or delete it later.

Consider placing all rulers on a dedicated layer with the following rational:

1. If you need to move or delete them, you know exactly which layer to activate to do so
2. Hiding the ruler layer will eliminate their visual obstruction to modeling in a single step.
3. Too many rulers can slow down performance, therefore a dedicated layer which can be deleted when dimensioning and alignment work is completed is an efficient way to manage rulers.
   
   

Move Ruler

To move a ruler, Click on Move Ruler (T) and then Click and hold on either end of a ruler and then drag it to move that end of the ruler. That is to say, you cannot move a ruler in its entirety and preserve its prior length, you can only displace one endpoint at a time. Therefore, any ruler movement most certainly implies a change in the ruler length. Just like the Add Ruler tool, the ruler will conveniently and continuously update its display of its length and angle to the world's north-south axis as you drag its endpoint.

Note that a ruler's layer must be unlocked to move its endpoints or else audio feedback will result. Since rulers have no property window that can be summoned, you cannot read what layer a ruler is on. Therefore, if you do not know what layer a ruler is on, it is suggested you unlock all layers before attempting to move a ruler.

When attempting to move a ruler endpoint in proximity to another, only one of the endpoints may be accessible to this tool. The accessible ruler endpoint may need to be moved temporarily before attempting to move the intended ruler.

Delete Ruler

Use Delete Ruler (Y) to delete the ruler. Leaving many rulers on the board may slow down the game.

Like the Move tool, the Delete tool should be employed at the endpoints or in close proximity to them in order to differentiate the ruler to delete. Also, similar to the move tool, a neighboring ruler endpoint may need to be displaced temporarily to delete a ruler being targeted for deletion. It is possible to delete rulers midspan when the camera is at high elevations, but with limited control (i.e. rulers further away can be deleted inadvertently).

Note that the ruler's layer must be unlocked to delete it. Since there is no way to read which layer a ruler resides on, it is suggested to unlock all layers when proceeding to a delete ruler(s) when its layer is unknown.

Other Facts About Rulers

• To change the scale of the ruler, go into the Surveyor Main Menu and choose Edit Route. Change the units to real Scale, HO, OO or whatever scale you prefer. You can also choose between Metric and Imperial.

• Rulers also conveniently display their angle to the world's north-south axis, which is very important for modeling because there are less than a handful of ways to measure angles/azimuth in Surveyor. Unfortunately, the precision of the angle display is merely to the nearest degree.

• Rulers always follow the contour of the terrain and render themselves a small distance above the ground. Therefore, when using rulers to align elevated splines like bridges, the projection of the spline points on the ground first need to be located to align spline using a ruler (i.e. the ruler will not project up to an elevated spline).

• Rulers obey layering behavior just like any other object or spline, but with the shortcoming that their layer cannot be identified or changed by summoning their properties using a "?" button -- rulers do not have this facility. Therefore, you cannot editorially change a ruler's layer, and you can never bind it to a secondary layer to use a bounding layer managing technique. If you you must move a ruler to a different layer, you must attempt to graphically recreate it on the desired layer, then delete the pre-existing ruler.

• For Trainz versions that have fast-switching between Surveyor and Driver, Rulers on a locked layer will hide themselves when reverting back to Surveyor from Driver until their layer is unlocked.
  
  

Camera Management Tools

You can place static cameras, which focus on a section of track until the whole train passes by, or lineside (tracking) cameras, which pan across following the train movement. To select which camera to work with, click on either of the arrows in the middle of the tool list to switch between Static and Tracking camera mode.

Place Camera

Before placing a camera, maneuver your normal viewpoint as close as possible to where you want to place the camera. Click on Place Camera (A), then Click exactly where your Compass meets the ground. This places the camera in 3D space, and puts you automatically into Move Camera (M) mode. A Green box and a flashing green light appear.

Move Camera

Use your zoom keys, and cursor keys to position the camera exactly as you want it to see in Driver, then Click again to lock the camera in place. A red camera means it is a static camera, and green is a tracking camera.

Delete Camera

To delete an unwanted camera, select Delete Camera (D) and Click on a 3D camera object.

Copying and Pasting Tools

Another very useful tool is the copy and paste function.

Select Area

Click on Select Area (B) and Click and drag to create a rectangle around the area you wish to copy. The white box shows the area that will be copied. Click on Cancel Selection (X) to cancel the selection.

Paste mode

Click on Paste Mode (P) and Click with the right mouse button to navigate around your terrain to the new location. Click where you want the selection copied.

Paste Rotation

You can also rotate your selection using the Paste Rotation dial (“[“ or “]”).

/// Paste Height, Textures, Objects or Track

You can control what is and is not copied and pasted. You can copy height, textures, objects or any combination by selecting and deselecting the appropriate icons. These are “toggle” switches. Whilst in Paste Mode, click on Paste Height, Paste Textures or Paste Objects to include or exclude those elements from your paste function. The buttons will remain highlighted in bright green if toggled “on”.

/ Absolute/Relative Height

You can paste either relative or absolute heights by Clicking on either icon to toggle between them. The default is absolute height.

Return To

• Surveyor Tools
• Surveyor