How to Control Junctions in Sessions
From TrainzOnline
(Difference between revisions)
m |
m |
||
| Line 12: | Line 12: | ||
The following applications give examples of using Session Rules to control junctions. | The following applications give examples of using Session Rules to control junctions. | ||
<br> | <br> | ||
| + | <table> <!-- BEGIN Nav Buttons Table --> | ||
| + | <tr valign="top"> | ||
| + | <td width=729><span id="stepApp1"></span> </td> | ||
| + | <td width=46>[[file:BackToTop.png|link=#top|alt=Top|Top]]</td> | ||
| + | <td width=75> </td> | ||
| + | <td width=75>[[file:NextDown.png|link=#stepApp2|alt=Next Down|Next Down]]</td> | ||
| + | <td width=75>[[file:BackToBottom.png|link=#bottom|alt=Bottom|Bottom]]</td> | ||
| + | </tr> | ||
| + | </table> <!-- END Nav Buttons Table --> | ||
='''Application 1: Presetting Junctions'''= | ='''Application 1: Presetting Junctions'''= | ||
| Line 67: | Line 76: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | + | <table> <!-- BEGIN Nav Buttons Table --> | |
| + | <tr valign="top"> | ||
| + | <td width=729><span id="stepApp2"></span> </td> | ||
| + | <td width=46>[[file:BackToTop.png|link=#top|alt=Top|Top]]</td> | ||
| + | <td width=75>[[file:NextUp.png|link=#stepApp1|alt=Next Up|Top]]</td> | ||
| + | <td width=75> </td> | ||
| + | <td width=75>[[file:BackToBottom.png|link=#bottom|alt=Bottom|Bottom]]</td> | ||
| + | </tr> | ||
| + | </table> <!-- END Nav Buttons Table --> | ||
='''Application 2: Asking the User to Set Junctions'''= | ='''Application 2: Asking the User to Set Junctions'''= | ||
| Line 138: | Line 155: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | <table> <!-- BEGIN Nav Buttons Table --> | ||
| + | <tr valign="top"> | ||
| + | <td width=729><span id="bottom"></span> </td> | ||
| + | <td width=46>[[file:BackToTop.png|link=#top|alt=Top|Top]]</td> | ||
| + | <td width=75>[[file:NextUp.png|link=#stepApp2|alt=Next Up|Top]]</td> | ||
| + | <td width=75> </td> | ||
| + | <td width=75> </td> | ||
| + | </tr> | ||
| + | </table> <!-- END Nav Buttons Table --> | ||
---- | ---- | ||
---- | ---- | ||
Revision as of 08:13, 16 August 2021
The information in this Wiki Page applies to TANE, TRS19 and Trainz Plus. It gives examples of how junctions can be controlled using Session Rules.
Contents |
 |
Junctions can be controlled by Session Rules during the running of a Session. |
The following applications give examples of using Session Rules to control junctions.
 |
 |
 |
Application 1: Presetting Junctions
 |
The Scenario: |
When a consist reaches a trigger, the junctions ahead are set and configured (e.g. locked/unlocked, AI control allowed/disallowed).
 |
Rules Used: |
- Trigger Check Rule to trigger the event.
- Set Junctions Rule to set junctions.
 |
Session Editor Screenshot: |
 |
 |
Description: |
- Line 1: Trigger Check The event is triggered when the consist reaches a trigger. This executes the following rule.
- Line 2: Set Junctions Sets selected junctions to set directions and specifies the level of control by the users and AI.
For example:-
 |
|
|
 |
|
Application 2: Asking the User to Set Junctions
|
The Scenario: |
A consist has been halted at a trigger placed in front of a junction. The user will be asked to set that junction and the following junction before the consist can proceed.
 |
Preconditions: |
- Navigation Display Rule to create a navigation point set.
|
Rules Used: |
- Wait on Navigation Point Rule to trigger the event.
- Message Popup Rule to open a message window on the screen.
- Multiple Junction Alignment Check Rule to test if specified junctions are set correctly.
|
Session Editor Screenshot: |
 |
|
Description: |
- Line 1: Wait on Navigation Point The event is triggered when the consist halts at the navigation point assigned to the trigger. This executes the following rules simultaneously
- Line 2: Message Popup Displays a message window asking that the next two junctions be manually set.
- Line 3: Multiple Junction Alignment Check tests the switch directions of the next two junctions and waits until they are aligned as specified.
 |
| Checking junction switch settings |
The following line is executed only if the junctions are set correctly
- Line 4: Message Popup Displays a message window stating that the junctions are now correctly set.
|
|
|
Trainz Wiki
 |
More Tutorials and Guides to Using Trainz |
This page was created by Trainz user pware in May 2018 and was last updated as shown below.
