How to Control Junctions in Sessions
From TrainzOnline
(Difference between revisions)
(→Application 1: Presetting Junctions) |
(→Application 2: Asking the User to Set Junctions) |
||
| Line 29: | Line 29: | ||
</table> | </table> | ||
| − | + | =='''Application 2: Asking the User to Set Junctions'''== | |
| − | ''' | + | ==='''The Scenario:'''=== |
A consist has been halted at a trigger placed in front of a junction. The user will be asked to set that junction and the following junction before the consist can proceed. | A consist has been halted at a trigger placed in front of a junction. The user will be asked to set that junction and the following junction before the consist can proceed. | ||
| Line 38: | Line 38: | ||
*'''[[Session_Rule_List_with_Parameters#Navigation_Display_Rule|Navigation Display Rule]]''' to create a navigation point set. | *'''[[Session_Rule_List_with_Parameters#Navigation_Display_Rule|Navigation Display Rule]]''' to create a navigation point set. | ||
| − | ''' | + | ==='''Rules Used:'''=== |
*'''[[Session_Rule_List_with_Parameters#Wait_on_Navigation_Point_Rule|Wait on Navigation Point Rule]]''' to trigger the event. | *'''[[Session_Rule_List_with_Parameters#Wait_on_Navigation_Point_Rule|Wait on Navigation Point Rule]]''' to trigger the event. | ||
| Line 44: | Line 44: | ||
*'''[[Session_Rule_List_with_Parameters#Multiple_Junction_Alignment_Check_Rule|Multiple Junction Alignment Check Rule]]''' to test if specified junctions are set correctly. | *'''[[Session_Rule_List_with_Parameters#Multiple_Junction_Alignment_Check_Rule|Multiple Junction Alignment Check Rule]]''' to test if specified junctions are set correctly. | ||
| − | ''' | + | ==='''Session Rules Screenshot:'''=== |
<table> | <table> | ||
<tr> | <tr> | ||
| Line 51: | Line 51: | ||
</table> | </table> | ||
| − | ''' | + | ==='''Example Explanation:'''=== |
*'''Line 1: Wait on Navigation Point''' The event is triggered when the consist halts at the navigation point assigned to the trigger. This executes the following rules simultaneously | *'''Line 1: Wait on Navigation Point''' The event is triggered when the consist halts at the navigation point assigned to the trigger. This executes the following rules simultaneously | ||
Revision as of 23:18, 30 May 2018
The screenshots shown below give examples of how junction settings can be used to control the operation of a session.
Contents |
Application 1: Presetting Junctions
The Scenario:
When a consist reaches a trigger, the junctions ahead are set and locked into position.
Rules Used:
- Trigger Check Rule to trigger the event.
- Set Junctions Rule to set junctions.
Session Rules Screenshot:
 |
Example Explanation:
- Line 1: Trigger Check The event is triggered when the consist reaches a trigger. This executes the following rule.
- Line 2: Set Junctions Sets selected junctions to set directions and specifies the level of control by the users and AI.
 |
Application 2: Asking the User to Set Junctions
The Scenario:
A consist has been halted at a trigger placed in front of a junction. The user will be asked to set that junction and the following junction before the consist can proceed.
2. Preconditions:
- Navigation Display Rule to create a navigation point set.
Rules Used:
- Wait on Navigation Point Rule to trigger the event.
- Message Popup Rule to open a message window on the screen.
- Multiple Junction Alignment Check Rule to test if specified junctions are set correctly.
Session Rules Screenshot:
 |
Example Explanation:
- Line 1: Wait on Navigation Point The event is triggered when the consist halts at the navigation point assigned to the trigger. This executes the following rules simultaneously
- Line 2: Message Popup Displays a message window asking that the next two junctions be manually set.
- Line 3: Multiple Junction Alignment Check tests the switch directions of the next two junctions and waits until they are aligned as specified.
 |
| Checking junction switch settings |
The following line is executed only if the junctions are set correctly
- Line 4: Message Popup Displays a message window stating that the junctions are now correctly set.
Trainz Creation Tutorials:
Related Session Creation Tutorials:
