HowTo/Tune a Diesel EngineSpec

From TrainzOnline
< HowTo(Difference between revisions)
Jump to: navigation, search
(Created page with "Test Track is a module designed to allow users to customise and tweak enginespecs. This How To Guide will walk you through the main steps to get you tweaking. From that poin...")
 
(Editing an Engine Spec)
 
(3 intermediate revisions by one user not shown)
Line 1: Line 1:
 
Test Track is a module designed to allow users to customise and tweak enginespecs.  
 
Test Track is a module designed to allow users to customise and tweak enginespecs.  
  
This How To Guide will walk you through the main steps to get you tweaking. From that point, it all comes down to finding the right data to ensure that your power cruves and braking curves match realistic expectations.
+
This How To Guide will walk you through the main steps to get you tweaking. One you understad the "how, it then comes down to finding the right data to ensure that your power cruves and braking curves match realistic expectations.
  
tbc
+
=Test Track Module=
 +
This module allows you to use a time slider to rapidly move through your testing cycle without having to wait until your train gets up to speed.
 +
 
 +
Start the module from the Launcher > File > Visit Test Track.
 +
 
 +
== Setting up your Track==
 +
* Click System Menu > New Test
 +
* Click Add Section and add as many sections as you require.
 +
* Adjust the section length, gradient and curve radius
 +
* Once you've set up a tick, click the tick to apply and save your changes.
 +
* Your track is drawn off into the distance.
 +
Note: We recommend you go uphill before you go downhill so that your track is "above ground".
 +
 
 +
== Placing your Consist==
 +
* Click the Train tab and place trains as you would normally
 +
* Use the Consist tab and Get tool to Get then save your consist for future testing
 +
 
 +
== Conducting a Test==
 +
* Expand the graph and choose which elements you wish to test.
 +
* Click Add to add, for example, Train speed, and Tractive Effort.
 +
* The graph will begin drawing. This graph is over time, so think of it like a recorder.
 +
* To get your train moving, release the brakes, increase the throttle as you would normally.
 +
* Notice that the graph lines change over time.
 +
* Click pause to stop the train motion, but notice the graph continues to "buffer".
 +
* Drag the time slider to the right to rapidly get further down the track (for example to the bottom of a hill you are testing your train on).
 +
* Click Pause again for the motion to continue.
 +
 
 +
==Editing an Engine Spec==
 +
* Click System Menu > Edit Engine Spec
 +
* To adjust the power curve, click the "click here to edit power curve" link.
 +
* The power curve indicates how many kiloNewtons (kN) of power is applied at various speeds (in m/s).
 +
* Click the tick to save your changes and follow the prompts to save in memory or to save a new version of the engine spec.
 +
* While the graph below looks pretty, it provides a very underpowered output at low notches (meaning it will accelerate very slowly in notch 1).
 +
 
 +
View your power curves here:
 +
 
 +
[[File:2018-08-28 140035.png|700px]]
 +
 
 +
 
 +
Change the m/s and Kn values here:
 +
 
 +
[[File:2018-08-28 140046.png|700px]]
 +
 
 +
In the above image, the numbers on the left are m/s and the numbers on the right are the tractive effort applied at that speed (in kN).
 +
 
 +
So at 3m/s there is a maximum tractive effort of 10.2kN.
 +
 
 +
If your train is accelerating too slowly, increase the power numbers. If your train is wheelslipping, reduce the numbers.
  
 
See Also:  
 
See Also:  

Latest revision as of 14:51, 28 August 2018

Test Track is a module designed to allow users to customise and tweak enginespecs.

This How To Guide will walk you through the main steps to get you tweaking. One you understad the "how, it then comes down to finding the right data to ensure that your power cruves and braking curves match realistic expectations.

Contents

[edit] Test Track Module

This module allows you to use a time slider to rapidly move through your testing cycle without having to wait until your train gets up to speed.

Start the module from the Launcher > File > Visit Test Track.

[edit] Setting up your Track

  • Click System Menu > New Test
  • Click Add Section and add as many sections as you require.
  • Adjust the section length, gradient and curve radius
  • Once you've set up a tick, click the tick to apply and save your changes.
  • Your track is drawn off into the distance.

Note: We recommend you go uphill before you go downhill so that your track is "above ground".

[edit] Placing your Consist

  • Click the Train tab and place trains as you would normally
  • Use the Consist tab and Get tool to Get then save your consist for future testing

[edit] Conducting a Test

  • Expand the graph and choose which elements you wish to test.
  • Click Add to add, for example, Train speed, and Tractive Effort.
  • The graph will begin drawing. This graph is over time, so think of it like a recorder.
  • To get your train moving, release the brakes, increase the throttle as you would normally.
  • Notice that the graph lines change over time.
  • Click pause to stop the train motion, but notice the graph continues to "buffer".
  • Drag the time slider to the right to rapidly get further down the track (for example to the bottom of a hill you are testing your train on).
  • Click Pause again for the motion to continue.

[edit] Editing an Engine Spec

  • Click System Menu > Edit Engine Spec
  • To adjust the power curve, click the "click here to edit power curve" link.
  • The power curve indicates how many kiloNewtons (kN) of power is applied at various speeds (in m/s).
  • Click the tick to save your changes and follow the prompts to save in memory or to save a new version of the engine spec.
  • While the graph below looks pretty, it provides a very underpowered output at low notches (meaning it will accelerate very slowly in notch 1).

View your power curves here:

2018-08-28 140035.png


Change the m/s and Kn values here:

2018-08-28 140046.png

In the above image, the numbers on the left are m/s and the numbers on the right are the tractive effort applied at that speed (in kN).

So at 3m/s there is a maximum tractive effort of 10.2kN.

If your train is accelerating too slowly, increase the power numbers. If your train is wheelslipping, reduce the numbers.

See Also:

Personal tools